Each weight is different and must be properly hung from the movement left, center, right to ensure proper operation. Weights are hung from the movement by a cable or chain. The weights must be raised at least every 7 days or the Grandfather Clock will stop. Raising cable driven weights is accomplished through use of a crank. Raising chain driven weights is accomplished by pulling down on the loose end of the chain.
The strike and chime sounds are made by a series of hammers hitting various length rods. Each rod makes a different sound when hit by a hammer. Specific chime melodies are achieved by controlling the sequence that each hammer hits a corresponding rod. Unboxing Your New Grandfather Clock: a Cut the nylon bands around the shipping carton and open the box from both side. This will contain your product manual. Located in the bottom of the shipping carton will be a white styrofoam box. This box contains: a a key to fit your Grandfather Clock door, b a crank which will be used to wind your Grandfather Clock and, c weights which operate the Grandfather Clock movement.
Also, within the shipping carton will be the Grandfather Clock pendulum packaged in a separate cardboard box. Move the Grandfather Clock close to its final location. Access to the Grandfather Clock movement, chimes and cables is made in three possible ways; through the front door s , through the top side panels or side doors on some Grandfather Clocks , or through the back access panel.
The top side panels are held from the inside by tape or a plastic clip. The plastic clip may be turned or tape may be removed permanently. Refer to the General Information section in section 10 for proper instructions to remove and install top side panels. Remove the cardboard sleeve from around the chime rods by first cutting the rubber band with scissors. Next, grasp the cardboard sleeve as marked and pull straight down and off the ends of the chime rods.
See figure 1. Remove the foam pads from between the chime hammers and chime rods by first cutting the rubber band with scissors. Care should be taken to avoid bending the chime hammers. The chime hammers will be free to move allowing easy removal of the foam pads. Remove the spring clip from the back side of the movement by first pulling one end free. If there is a long cardboard sleeve and no rubber bands, simply pull down slowly on the cardboard sleeve from the front of the clock and the packing will release on it's own.
Then pull out the foam behind the chime hammers and you have completed this step. This is one of the most critical points in the entire set-up operation. Doing so at this time could cause the cables to overlap and bind the movement. You can remove the styrofoam blocks AFTER your Grandfather Clock is totally set up and has been operating for about twelve 12 hours or when they are completely free to remove.
Some pendulums have a colored protective plastic film covering the pendulum disk. Carefully remove this film before hanging the pendulum. To hang the pendulum, locate the pendulum guide through the front door, or any of the side or back access panel locations.
While holding the pendulum guide with one hand, slip the pendulum in through the front door with your other hand. Place the pendulum hook over the pin or through the slot on the pendulum guide, and lower the pendulum until it is hanging securely on the pendulum guide.
See figure 3. Reach through the front door of the Grandfather Clock and place your hand on the side of the pendulum disk. Move the pendulum to the far left of center and release. Let the Grandfather Clock operate a few minutes until the pendulum settles into an even swinging motion. See figure 7. If your Grandfather Clock gains or looses time after twenty-four 24 hours, see General Information Section to regulate the timekeeping of your Grandfather Clock. After the Grandfather Clock has run for at least twenty-four 24 hours, remove the styrofoam blocks by lifting the blocks straight up until they clear the cable pulley.
Then gently push them back, through the cables. NEVER wind a cable drive movement without weights installed. When removed, you have access to the Grandfather Clock movement and chime area.
The panels may be held in place during shipment by tape or a plastic clip. In order to remove the panel, reach in through the front door and turn the plastic clip or remove the tape. Then follow these steps: 1. Grasp the wood slats or knob with the tips of your fingers. Be careful not to push on the grill cloth or glass as you might separate it from the wood top side panel. Lift the top side panel up. It rests in a groove on the bottom edge. Push the bottom edge of the top side panel toward the center of the case while at the same time, pull the top edge down and out of the groove in the top of the opening.
Tilt the top edge of the top side panel toward the case center. Remove the top side panel from frame opening, bottom end first. When installing wooden or glass top side panels reverse steps 1 thru 5.
Check correct time. Compare time shown on your Grandfather Clock with correct time. It is attached to gears with special-shaped teeth. These escapement gears are attached to a weight drum wound up by chains or cables. Under the lens NFRA member under lens for audit gaps in fraud-hit firm; cloud over selection process for regulatory posts. Subscribe to ETPrime. Browse Companies:. Find this comment offensive? This will alert our moderators to take action Name Reason for reporting: Foul language Slanderous Inciting hatred against a certain community Others.
Your Reason has been Reported to the admin. Fill in your details: Will be displayed Will not be displayed Will be displayed. Share this Comment: Post to Twitter. Already an ET Prime Member? Sign In now. Limited Access. Subscribe with Google. Yearly Save The hands of the clock, which show the time as they move around the dial, are typically mounted on timekeeping gears.
These gears can automatically turn and move the hands at their respective speed. What makes the timekeeping gears work is the existence of the weight, which is properly regulated by the power gears and the pendulum.
Clocks have been very helpful for timekeeping, which paved way for their numerous developments throughout the centuries. While analogue and digital clocks have been the standard options for clocks today, conventional clocks are still known today for their distinctive decorative and antique value. For more information about grandfather clocks, feel free to contact us at Ken Ross Jewellers. Optimized by: Netwizard SEO.
Ken Ross Jewellers have been in business for over 50 years, producing and maintaining fine jewellery and watches.
0コメント